Ace Hardware Home Security System 3108651 User Manual

Note: For under-eave installation, rotate the sensor head 180° by  
bending the sensor towards the clamp bracket. Rotate the sensor  
bottom clockwise away from the bracket.  
Motion Sensing  
Light  
®
2. Aiming  
As an ENERGY STAR® Partner, Heath®/Zenith has  
determined that this product meets the ENERGY  
STAR® guidelines for energy efficiency. This product  
is ENERGY STAR® compliant when used with 120  
Watt bulbs.  
The coverage area for the sensor is shown in Figure 2. The sensor  
should be aimed so that the motion to be detected is in front of and  
across the coverage area. The sensor should be aimed looking out at  
a horizontal angle. To reduce false triggering, point the sensor away  
from traffic areas, air conditioners, dryer vents, water pools, or  
anything which may move or change temperature rapidly.  
Models 3108677/3108651/3108669  
Note:Installationofthislightcontrolshouldbedoneonlybythose  
with experience in 120 Volt household wiring. Some local codes  
may require that a licensed electrician install the light control.  
180°  
8 Ft.  
This light control automatically turns on lights when motion is  
detected.  
70 Ft.  
Two lamp holders are provided. The lamp holders are rated at 150  
watts max. each.  
Figure 2 - Coverage Angles  
3. Testing  
1. Installation  
Turn the power back on at the circuit breaker. Turn the light switch  
on.  
Note: When first turned on wait about 1 1/2 minutes for the circuitry  
Caution: Always turn the circuit breaker off when wiring  
the fixture.  
1. Remove the existing fixture.  
to calibrate.  
2. The plastic hanger can be used to hold the fixture while wiring.  
The small end of the plastic hanger can be threaded through the PuttheTIMEswitchonthebottomofthesensorintheTESTposition.  
hole in the center of the cover plate. The small end then goes into You can now walk in front of the unit and the lights will come on for  
one of the slots on the mounting strap.  
about 5 seconds. The TEST mode works both day and night.  
3. Connect the light control as shown in Figure 1:  
Black sensor wire to the black (HOT) house wire.  
White sensor wire to the white (NEUTRAL) house wire.  
Walk through the coverage area and point the sensor to obtain the  
desired coverage area. Adjust sensitivity as needed.  
4. Operation  
White to white  
Black to black  
From House  
For motion sensing, put the ON-TIME switch on the bottom of the  
sensorinthe1, 5or10minuteposition. Whenmotionisdetected, the  
lights will come on the selected time. Note:The photocell keeps the  
lights from turning on in daylight.  
Push the rubber  
plug firmly into  
place  
Tokeeplightsonallnight, flipthelightswitchofffor1secondthen  
back on. Turning the light switch off for 1 second then back on will  
return the control to the motion sensing mode. At dawn, the control  
will return to the motion sensing mode and shut off.  
House ground wire to green  
ground screw on fixture.  
Specifications:  
Figure 1 - Wiring at Junction Box Plate  
Total Lighting Wattage...................... Up to 300 Watts Maximum  
Lamp Holder Wattage ............... Up to 150 Watts Maximum each  
Range ............................................................................ up to 70 ft.  
Time Delay ...................................................... 1, 5, or 10 minutes  
4. Attachthefixturetothemountingstrapwiththecentermountingbolt.  
Use a weatherproof sealant to seal the fixture to the junction box.  
5. Install the protective lamp shields on the lamp holders by lining  
up the groves on the narrow end of the shields with the dimples  
in the lamp holders, push the shields into the lamp holders and  
turn clockwise slightly.  
6. Install the lamps in the lamp holders. Do not over tighten.  
7. Adjustment lamp holders. The lamps should be at least 1 inch  
away from the sensor.  
Caution: This product is to be used with a U.L. listed rain tight or  
wet location suitable outlet box. Depending on the installation,  
additional hardware may be required.  
Caution: Do not mount the sensor above or touching the lamps  
(keep 1 inch or more from the lamps). The sensor bottom must be  
facing down for best coverage and to avoid water damage and  
electrical shock.  
© 2003  
595-5751-02  
 

Able Planet Stereo Amplifier PS1600BTE User Manual
AEG Washer 70630 User Manual
Alpine Car Amplifier MRX M100 User Manual
Alpine CD Player CDA 7873R User Manual
Amana Dishwasher ADB1600AW User Manual
AMX Stereo Amplifier DAS TAMP4 SIG User Manual
AMX Switch AV2SM User Manual
AVerMedia Technologies Security Camera EB1304 User Manual
Barco Projector R5976907 00 User Manual
Beko Clothes Dryer DPY 7504 XB1 User Manual