Allied Telesis Power Supply AT WDRPS 10 User Manual

Related Documents  
To install the AT-WDRPS-10, perform the following procedure:  
way to access the most recent documentation, software, and technical information  
for all of our products. For details on the features and functions of your Allied  
Telesyn AT-WD1008 chassis and modules, refer to the following manuals from our  
web site:  
Note  
The AT-WDRPS-10 unit can be installed while the multiplexer is powered ON.  
You do not need to power OFF the multiplexer to install the RPS.  
AT-WD1008 Gigabit Ethernet Wavelength Division Multiplexer  
1. Loosen the two thumbscrews that secure the blank faceplate over the right-  
hand redundant power supply expansion slot located on the front panel of the  
AT-WD1008 Multiplexer and remove the cover.  
Installation Guide  
PN 613-50367-00  
AT-S47 Management Software Users Guide  
S
T
TX  
PN 613-50371-00  
TX  
L
N
K
T
S
T
X
X
RX  
AT-WDRPS-10  
Redundant Power Supply (AC)  
L
N
K
T
S
T
T
TX  
WEST  
RX  
T
R
X
X
EAST  
R
RX  
TX  
RX  
L
N
K
T
S
T
TX  
E
A
N
S
T
O
R
M
A
L
C
H
5
RX  
TX  
TX  
Package Contents  
C
H
6
RX  
TX  
RX  
RX  
TX  
Installation Guide  
C
H
7
TX  
RX  
Make sure the following items are included in the shipping package. If any item is  
missing or damaged, contact your Allied Telesyn sales representative for  
assistance.  
F
AN  
A
B
P
O
S
W
E
N
M
R
B
S
P
U
M
P
O
P
D
U
L
Y
L
E
C
H
8
F
AN  
One AT-WDRPS-10 Redundant Power Supply (AC) Module  
One AC Power Cord  
Allied Telesyn, Inc.  
960 Stewart Drive, Suite B  
Sunnyvale, CA 94085 USA  
This installation guide  
Tel 1 (408) 730-0950 • Fax 1 (408) 736-0100  
Warranty card  
2. Remove the AT-WDRPS-10 unit from its shipping package.  
3. Slide the AT-WDRPS-10 unit into the RPS expansion slot.  
Installing the AT-WDRPS-10 Power Supply  
T
X
TX  
RX  
L
N
K
T
S
T
X
X
R
X
T
L
N
Caution  
K
T
S
T
T
X
X
X
W
E
T
S
R
T
E
A
S
R
T
R
X
TX  
RX  
L
N
K
T
S
T
T
X
EAST  
TX  
N
O
R
M
A
L
Before installing the module, refer to the AT-WD1008 Installation Guide for  
electrical safety and emission information.  
CH  
5
R
X
T
X
CH  
6
R
X
TX  
RX  
RX  
T
X
Overview  
CH  
7
TX  
RX  
F
AN  
A
B
POWER  
SNMP  
SUPPL  
MODULE  
Y
B
CH  
8
The AT-WDRPS-10 is an AC Redundant Power Supply (RPS) for the AT-WD1008  
Multiplexer chassis. When installed, the unit shares the load of powering the  
chassis with the standard power supply that comes pre-installed in the chassis. If a  
power supply fails, the remaining unit provides all power to the system, thereby  
preventing a network failure. The power supply is hot-swappable, meaning that  
you can install it while the chassis is powered ON.  
F
AN  
Caution  
Do not install the AT-WDRPS-10 module in an AT-WD1008 chassis designed  
for DC power. An AC powered chassis has two AC power sockets on the back  
panel.  
P
O
W
E
R
F
A
U
L
T
P
O
W
E
R
F
A
U
L
T
PN 613-50369-00 Rev A  
1
2
3
 

Acer Computer Monitor AL2216W User Manual
Adder Technology Computer Accessories CATX USBA DA User Manual
AEG Cooktop FM 6300G AN User Manual
AGFA Digital Camera DC 1338i User Manual
Aiphone Intercom System GH 1AD User Manual
Alpine Home Theater Server PXI H990 User Manual
American Standard Bathroom Aids 10 GPF User Manual
Asus Car Video System VH222 User Manual
Axis Communications Security Camera P5532 User Manual
Banner Stud Sensor P4 GEO 13 User Manual